Your Step-by-Step Guide to Setting Up the Chinacnczone Handheld Pulse Laser Cleaner

🔍 1.1 Unpacking Inspection

1. Inspect Packaging & Machine:

   • Check for visible damage to the box or Chinacnczone Handheld Pulse Laser cleaning machine.

   • If damage is found (e.g., dents, cracks), photograph it immediately and contact Chinacnczone/Scotle after-sales:
     

2. Verify Accessories:
   Cross-reference contents with the Packing List :

   • Laser cleaning gun (FWH50-P10A)

   • 4x protective lenses

   • Positioning frame, side-blowing module

   • Protective glasses, gloves

   • Blowing device parts
     Missing items? Photograph and notify after-sales.

⚙️ 4.2 Machine Installation of Chinacnczone Handheld Pulse Laser cleaner

4.2.1 Air Compressor Connection

Essential to prevent lens contamination from smoke/debris.

• Requirements:

  • Power: ≥750W

  • Air Volume: ≥15L

  • Pressure: ≥0.2MPa
    (Machine does NOT include a compressor – source separately)

• Connection Steps:

  • 6mm Pipe: Press the blue port collar, remove the transparent tube, and insert your pipe.

  • 8mm Pipe: Connect directly to the dedicated 8mm port.

4.2.2 Positioning Frame Installation

Critical for precise focal length!

• Why Install? Ensures optimal focus without manual adjustment.

• Steps:

  1. Secure the frame using M4×10 screws (bottom first, then top).

  2. Note: Frame height varies by field lens (F160/F210/F254/F330).

• Usage Tip:

  • Small parts ➔ Use frame for accuracy.

  • Large surfaces ➔ Frame optional; manually adjust gun height until the laser spot is brightest.

4.2.3 Side-Blowing Module

• Purpose: Blows residual dust off the cleaned surface.

• Installation: Attach to the cleaning head (refer to Page 17 diagram).

⚡ 4.3 Powering On & Interface Overview

1. Laser Switch: Turn on (located on the machine body).

2. Open Laser Head Cover: Remove the protective dust cover.

3. Touchscreen Menu:

   • [Main]: Real-time monitoring, scan/laser parameter adjustments.

   • [Parameter]: System settings, language, permissions.

   • [Advanced]: Restricted settings (password-protected).

4. Start Sequence:

   • Tap [Ready to Clean] on the [Main] screen.

   • Double-click the laser head button to start emission (single-click = preview).

   • To stop: Single-click the laser head button → Tap [Stop Cleaning].

⚙️ 4.4 Parameter Settings of Chinacnczone Handheld Pulse Laser cleaning machine

4.4.1 Material-Specific Presets (Quick Start!)

Use these tested settings for common materials (Page 20):

💡 Key Parameters:

• Power (%): Adjust cleaning intensity.

• Scan Speed: Slower = deeper cleaning.

• Lens Choice: F160 (small spot) for detail; F254 (wide spot) for efficiency.

4.4.2 Manual Parameter Adjustment

Refine settings via the [Main] screen:

1. Adjust:

   • Laser power (W)

   • Pulse width (ns)

   • Frequency (kHz)

   • Scan speed (mm/s)

   • Scan width/length

2. Preview: Tap [Scan] to test the laser path; tap [Blowing] to check air assist.

⚠️ Critical Notes:

• 200W vs. 300W Machines:

  • 200W: Uses F210 lens (max scan width = 125mm).

  • 300W: Uses F254 lens (max scan width = 145mm).

• Never look directly at the laser spot! Always wear protective goggles.

Language & Calibration

• Language: Set in [Parameter] → Choose English/Deutsch.

• Laser Center Offset: Tap [Offset] and adjust X/Y values if the beam is misaligned.

🛡️ Safety First!

• ALWAYS wear laser goggles (Class 4) and flame-resistant gloves.

• Work in ventilated areas; use fume extraction if needed.

• Keep flammable materials away – sparks can cause fires!

• Never disassemble the machine – contact support for issues.

The Chinacnczone Handheld Pulse Laser cleaning machine product link as below

https://scotlelaser.com/collections/pulse-laser-cleaning-machine/products/jpt-pulse-laser-cleaner-cleaning-machine-air-cooled-laser-oil-paint-rust-remover